Direct password Entry because that GE remotes v 4 digit codes

The complying with is a brief tutorial on programming most models the GE universal remotes through 4 number codes. See additionally this page for basic GE remote password entering instructions.

Step 1: Press and hold the "SETUP" button until the indicator light transforms on, climate release.

Step 2: Press and release the desired Mode switch (TV, DVD, CBL/SAT, etc.). The indicator light will certainly blink, then remains lit.

Step 3: enter the 4 digit password for her device. After a valid code entry, the indicator light turns off. Because that an invalid code, the indicator light flashes.

You are watching: Ge universal remote 24993 code list

Step 4: through your an equipment on, test a few common attributes like "CHANNEL Up/Down" or "VOLUME Up/Down" , "MUTE", etc. If the device responds, no additional programming is required. If part buttons don"t job-related as lock should, shot a various code provided for your brand.

NOTE: The indicator light will either be a small red LED at the optimal of the remote or the illuminated "ON/OFF" button.

About codes supplied in GE/Jasco remotes


*
*

There were multiple 4 digit code versions provided in GE remotes over time, indigenous V1 (2006), V2 (2011), V3, V4 (2012), V5, CL3 (2013), CL4 (2016) come the newest CL5 (2019).

To find out the variation your far uses, open the battery compartment, remove the batteries and locate the sticker containing the model number. A variation 2 with Version 5 remote will have actually a "V2" come "V5" after ~ the design number. Older remotes through no variation after the model# usage the V1 code list. The newest ones will be CL3, CL4 or CL5.

In order to conserve you the hassle of going with multiple code tables, we have actually compiled together the code lists from various versions the GE remotes share the very same code basic (e.g. V2&V4, V3&V5). If your remote is contempt old, you"ll obtain the advantage of finding the password for your machine even if it appeared after her remote to be manufactured, but uses one old password that currently exists preprogrammed in your model. Friend can likewise find the password for some old tools that are dropped indigenous the password lists, however still supported by newer remote controls. The only downside the this method is, that there will certainly be a few codes the are only supported by a specific version. So, if a code listed for your brand is not sustained by your remote, try the following one from the list.

Sometimes a code will certainly be accepted, yet only allow minimal function manage (e.g. Only volume and also channel control). In this case, proceed programming using the following code number for the brand.

Auto code Search (for newer models)

The Auto password Search searches immediately through every one of the password stored in her remote. If your an equipment does not respond to any kind of of the codes provided for your device, or her brand walk not appear in the code lists, shot the complying with steps:

Step 1: Manually rotate on the machine you great to control.

Step 2: Press and hold the "SETUP" switch until the indicator light stays on, then release.

Step 3: Press and also release the desired device button ~ above the remote (TV, DVD, CBL/SAT, etc.). The indicator light will blink once and also then continue to be on.

Step 4: v the far pointed in ~ the device, press and also release the "POWER" switch on the far once. Wait patiently until the remote sends out a batch that 10 codes to the device. The indicator light will blink as soon as for every code and remain top top after sending the 10 codes. Repeat this step again and again until your maker turns off.

Step 5: as soon as the an equipment turns off, manually turn the device back on.

Step 6: v the far pointed at the device, press and release the "VOL+" switch until the machine turns off. The remote will certainly resend the critical 10 codes one through one. Be certain to wait around 3 secs after each "VOL+" switch press to permit the device time to respond.

Step 7: when the machine turns off, press and also release the same machine button girlfriend pressed in action 3 to keep the code.

Notes:

The "VOL–" button can be used to go backwards through each batch that 10 codes.The indicator light will flash 2 time after experimentation the first or last password in every batch of 10.Test the buttons ~ above the far to view if the maker responds together you would expect. If not all buttons work as castle should, repeat this process to search for a far better code.Repeat this procedure for each machine you great to control.

Auto code Search (for older models)

Step 1: Manually turn on the an equipment you great to control.

Step 2: Press and hold the "SETUP" switch until the red indicator light continues to be on (around 4 seconds) and also then release the button.

Step 3: Press and release the desired maker button ~ above the far (TV, DVD, CBL/SAT, DVR/AUX). The red indicator will blink once and remains on.

Step 4: suggest the remote at the device and press and also release the "POWER" switch (for TV) or "PLAY" switch (for DVD, VCR, etc.) to begin the search. The red indicator will flash (approximately every 2 seconds) together the remote searches. The remote have to be pointed at your machine for the entire duration the this search.

Step 5: ar your finger top top the #1 switch so friend are prepared to lock-in the code.

Step 6: as soon as the an equipment shuts off or starts playing, press the #1 button to lock-in the code. The red indicator irradiate will revolve off. Note: girlfriend have roughly two secs after the machine shuts off or starts playing to lock-in the code.

Step 7: point the far at your machine and check to check out if the remote operates it as desired. If the does, no additional programming is required. If the does not, go back to step 2 and start the auto find again.

See more: Never Put Your Eggs In One Basket '? Don'T Put All Your Eggs In One Basket

Code search instructions for some older GE remotes

Step 1: Manually revolve on the machine to it is in controlled.

Step 2: Press and hold the "SETUP" button until the red indicator continues to be on, then release.

Step 3: Press and also release the desired Mode switch (VCR, TV etc.). The red indicator will blink once, then continues to be on.

Step 4: press the "POWER" (or "CHANNEL UP" for some versions) button repeatedly till the device to be controlled powers off (or transforms channel). The red indicator will blink through each keypress. When all codes have been searched the red indicator flashes promptly for 3 seconds.

Step 5: Press and release "ENTER" (or "MUTE" or "SAVE") switch to download the code. The indicator irradiate goes off.

Generally it"s ideal to save VCR password under the VCR button, cable password under CBL, and so on. If you want to store a VCR code under CBL, etc., very first follow the procedure for direct Code Entry and press CBL in step 2 of straight Code Entry, then enter any type of VCR password in action 3 of direct Code Entry. Climate follow the steps above for code Search.